The task of using a chainsaw or tree safely goes beyond ensuring. It is important to take this matter very seriously. As a chainsaw operator, there are a number of tree safety items. That you will need to wear at all times when you are working with a chainsaw. However, here are the most important ones that you will need to wear as you work. The logger’s head is especially useful when the tree is down. A major cause of tree safety injuries is bending branches. Invest in earplugs and a facial screen to shield your ears and eyes from the noise. Glasses that prevent dust from entering the eye as well as protecting the eyes from harm. Kevlar chaps that will stop a chain in a matter of seconds if you happen to accidentally fall the bar onto your leg, as you walk across a track.
Buy Felling Wedges
Two wedges for felling made of plastic keep your saw from being stuck during cutting. These are available at any store selling outdoor power equipment that sells chainsaws.
Calculate the Felling Zone How do you cut down a tree in the direction you desire
In reality, trees are taller and can reach higher than you might imagine tree service evansville. I used to use this trick in order to find out where a tree would fall when cutting down trees, however, it has never failed me. Here’s how to feel a tree’s movement in the direction you prefer by holding an Ax handle at a long distance. The closing one eye and then turning away or towards your tree till the peak of your ax is level. Both the tree’s top as well as its lower part are at the same height from the ground at its base when measured in the middle. Approximately where the top of the tree is going to be when the tree falls, your feet ought to be situated. It’s just an estimation, so keep in mind that the tree could hit something if you don’t leave enough space around it.
Clear a Cutting Zone
The tree is not ready for cutting down if you are unsure of which direction the branch is going to fall. Get rid of all the debris around the trunk of the tree and create two ways for you to escape to the side of the tree that is not falling. They should be placed approximately 45 degrees apart, in opposing directions, and in the same plane. In order to avoid falling in the event that a fallen tree falls on your foot, the most important thing is not to fall.
Size Up the Tree
Begin by looking at the tree. Do not cut it down if you observe:
The dead branches may be damaged, but still attached or the dead branches may be damaged and supported by the branches nearby. There is a good chance that a branch will break and fall over you, which will cause you to fall.
This tree leans to one side or the other as a result of the branches growing. The opposite side of the tree too heavily loads one side of the tree. There will be a tendency for it to move in the direction of the lean or load. Regardless of how much effort one puts into it.
It is possible that you will be able to observe buildings and fences, power lines, or other items that you are concerned about when felling trees. It is advisable to avoid the sensation and seek the advice of an expert if this is the case.
Anatomy of a Proper Notch
In general, when it comes to tree safety, the general rule of thumb is to make the notch about one-fifth the diameter of the tree’s trunk when cutting it down. It is the hinge that will guide the tree in the direction you wish it to fall in if the tree begins to fall.
Plan the Notch
The first step is to cut a notch along the trunk’s “fall” side. The handle of the saw should be adjusted to point towards the direction you intend to descend. Then look at the handle again. The area where the bar is in contact with the bark is the point at which you will cut the notch, and this is the area where you will cut it. The first thing you should do before cutting the bark is to draw out the notch either by marking it with chalk or scoring the bark using a chainsaw. If you are working from a high position, create the notch so that it is at a comfortable level for you to work. If you decide to cut the stump in the future, you will always have the option to do so.
Cut the Notch
The best way to start cutting is to start with the top and work your way down. In order to control the throttle control using your thumb, you will need to adjust your hand as you make cuts in the lower cut. After ensuring that you have met, you will be able to see that the top of the notch and the wedge are falling into the hole. To make the wedge fall free, you’ll most likely need to cut at either bottom to allow for more clearance for the wedge to fall.
Use Wedges on Big Trees
A tree safely that is over 18 inches in diameter should be felled if you intend to do so. After determining the diameter of the cutting hole, you can proceed with the notch and then begin cutting along it. Once you have gone deep enough when cutting through. The bar to buy wedges to hold it together, you should stop cutting. With the saw on and the bar in the cut, lock the chain brake and tap into the wedges in order to keep the bar in the cut. Then finish the cut by making sure that it looks good. It is important to use wedges to prevent the saw from getting stuck in the cut if the tree is leaning back while being cut.
Make the Felling Cut
Draw a line that connects the notch’s apex on both sides as cutting guides. The back cut must be straight and parallel to the edge of the tree. Then, make the felt cut. As soon as the tree begins leaning. Pull the saw away, set the chain brake, and walk away on any route you choose. Keep your eye on the tree to react if it doesn’t fall as you expected. Don’t let your eyes wander off of a fallen tree.
A Lookout Might Save Your Life
Suppose you are attempting to tree safely. In that case, it is much more secure. If you have an experienced and reliable assistant standing a couple of feet in front. You watch on the tops of trees for fallen branches and notify you when the tree is beginning to fall. You can have your assistant tap your shoulder with an object to let you know. When it’s time for you to leave the space. If it’s the beginning of the cutting and you receive the tap, exit the cutting machine and go away immediately. It means that the branch is going down. At the point where the branch is at the end of the cutting. The tapping indicates that the tree has begun its descent.
Start Cutting Branches at the Trunk
After you have cut down the tree, take branches off starting from the lower part of the tree safely and work up to the top. If you can, standing on the uphill part of the tree is best. Work on to the right side of the tree (as you are facing towards the tree’s highest point). This allows the chainsaw’s most secure possible and efficient operation as it can rest the side. The bottom portion of your saw onto the tree safely branches off with the pivoting movement.